Short answer
It can be. Batts and blown insulation are finished products; spray foam is manufactured on site by the installer, so the questions change. Three things decide the result: which product the company is authorized to buy, how often its spray rig runs, and how many board feet the person on the gun has sprayed. A company with a full-time foam division will answer all three without blinking. A company that pulls the rig out a few times a year has to overcome what idle time does to the isocyanate side, and the manufacturers' own maintenance schedules say how short that clock is.
How FoamGuard handles it
- Spray foam is the only thing we install. FoamGuard does not sell batts or blown-in, so the equipment is kept on the manufacturer's weekly schedule, sprayed or purged, parked nightly, screens and wet cups checked, and the whole job is one trade. The Agreement binds us to the manufacturer's published specifications and application guidelines (Section 9).
- The material is the authorized product. FoamGuard is a certified installer for Huntsman and BASF and sprays their closed-cell foams; every set is recorded by lot number and traceable to its manufacturer's batch.
- The mix is proven before your wall. Test patterns on cardboard until the foam is right; if a pass ever comes out off-ratio we stop, cut out the fresh foam, find the cause and test again. Off-ratio or improperly cured foam is one of the defects A Craftsman's Promise covers for five years (Section 14).
From the Project Agreement, Sections 9 and 14.
What's typical elsewhere
Graco, which builds the Reactor proportioners, writes the maintenance clock into its training checklist: "purge material if not spraying weekly" and "If system not being used for 1-2 weeks purge or circulate material," because isocyanate "crystallizes, plugs filters, damages seals." Its Reactor manual explains why: exposure to humidity makes the isocyanate "partially cure, forming small, hard, abrasive crystal," then "a film will form on the surface and the ISO will begin to gel."
The industry measures an installer by volume. The SPFA certifies an Installer at 100,000 board feet of spraying experience and a Master Installer at 500,000. The manufacturers measure by authorization: Huntsman "only sells to qualified contractors," and BASF's guidelines accept training only from verifiable sources such as its own training center or the SPFA program. A company that treats foam as an add-on can meet every one of these marks; the point is to ask, because the answers are specific.
Three questions that settle it
- Which product, and are you authorized to install it? The answer is a product name and a yes, not "closed-cell foam."
- When did the rig last spray a job, and when were the A-side screens and wet cups serviced? A weekly rig has a weekly answer.
- How many board feet has the installer on my job sprayed? Compare with the SPFA's 100,000 and 500,000 marks.
Read why spray foam equipment can't sit idle for the schedule the rig has to keep.
Want a number for your own project? Price My Project, book a free visit or call (814) 208-3478.
Is fiberglass or cellulose installed by the same crew a problem?
No. Those are finished products and their quality depends on fit and coverage, not on a chemical reaction at the gun. The add-on question is only about the foam.
What goes wrong when the rig sits?
Moisture in the air partially cures the isocyanate into abrasive crystals that restrict the A-side screen and wear the pump seals. The A pressure falls below B and the gun sprays off-ratio foam.
Does FoamGuard install other insulation?
No. FoamGuard sprays closed-cell and open-cell foam only. Where another material is the better choice for part of a building, we say so and leave that part to someone who installs it every day.
Sources
- Graco: Reactor Startup Checklist, Reactor & Fusion Training (Oct. 23, 2006)
- Graco: Reactor E-30 Operation Manual 333023, rev. U (Moisture Sensitivity of Isocyanates)
- Spray Polyurethane Foam Alliance: Individual Certification Programs
- Huntsman Building Solutions: How to buy (US)
- BASF: WALLTITE Series HFO Spray Foam Insulation Application Guidelines (Feb. 9, 2023)
