Short answer
FoamGuard sprays closed-cell foam in new houses after rough-in inspections and before drywall: about 3.5 inches in 2×6 walls for R-23 or more, 2 to 3 inches at rim joists and 3 to 7 inches on unvented roof decks, sealed for the blower-door test.
Key points
- Spray foam goes in after rough-in and framing inspections, before the insulation check and drywall.
- Pennsylvania's 2021 code, in force since January 1, 2026, asks zone 5 houses for R-23 walls and R-49 ceilings.
- Closed-cell foam is about R-7 per inch aged, an air barrier material at 1.5 inches and a Class II vapor retarder by about 2 inches.
- Prescriptive-path houses must test at 3.0 ACH50 or tighter; a house that tight needs mechanical fresh air.
- Foam in living space goes behind a 15-minute thermal barrier, such as ½-inch drywall.
What a new Western PA house needs from its insulation
Closed-cell spray foam gives a new house insulation, an air barrier and a vapor retarder in one bonded layer, at about R-6.3 to R-7.4 per inch aged, about twice fiberglass or cellulose.
Erie and most of Western Pennsylvania are climate zone 5. Erie averages 28°F in January, its heating design temperature is about 11°F, and lake-effect bands can drop 2 to 3 inches of snow an hour. Summers are humid.
Pennsylvania's 2021 code asks a zone 5 house for R-23 walls (or R-20 + R-3.8 continuous, or R-13 + R-7.5 continuous), R-49 ceilings, air-sealed and insulated rim joists, and a blower-door test. Under an unvented roof deck, IRC R806.5 requires foam rated as a Class II vapor retarder, at least R-20 when batts go below.
| Area | Foam | Typical thickness | R-value | Why |
|---|---|---|---|---|
| 2×6 walls | Closed-cell | 3.5 in. | R-26 on one HFO data sheet | Meets R-23 in one layer |
| Walls, flash and batt | Closed-cell + kraft-faced batt | 2 in. foam | R-14 foam + R-13 batt | Foam face stays above the dew point |
| Rim joists | Closed-cell | 2–3 in. | R-14 to R-21 | Seals sill joints; may stay bare up to 3¼ in. |
| Roof deck, all foam | Closed-cell | About 7 in. | About R-49 | Meets the ceiling value; attic ducts end up indoors |
| Roof deck, hybrid | Closed-cell, batts below | About 3 in. | R-21 foam; R-49 with batts | R806.5 minimum |
| Pipe and wire holes | Closed-cell | Fills the gap | Air seal | Metal flues get flashing and high-temperature caulk instead |
A vented attic with no ducts reaches R-49 for less with blown insulation on its floor; there we foam the walls and rim joists (sealed attics).
Flash and batt, closed-cell or batts and wrap
All three can meet the code; the air barrier is what differs.
In flash and batt, the foam's inside face must stay above the indoor dew point, 41°F at 70°F and 35% humidity. On an average Erie January day it sits near 42°F behind 1 inch of foam and 50°F behind 2, so we spray 2 inches, with kraft facing on the room side, never sheet plastic.
| Closed-cell, partial or full fill | Flash and batt | Fiberglass batts + wrap and air sealing | |
|---|---|---|---|
| PA zone 5 wall path | R-23 or more at 3.5 in. in a 2×6 | 2 in. foam (R-14) + batt (R-13) = R-27 | R-21 batt + R-3.8 continuous outside, or R-23 mineral wool |
| R per inch | About R-7 | Foam R-7; batt R-3.7 | R-3.7 to R-4.3 |
| Air barrier | Yes, listed at 1.5 in. | The foam layer | The wrap, tape and hand-sealed holes |
| Vapor control | Class II by about 2 in. | Class II foam + kraft facing | Kraft facing, Class II (1.0 perm) |
| Seams, framing, holes | Bonded to studs, plates, wires and pipes | Same; batts must touch the foam | Each box, wire and pipe sealed by hand |
| Blower-door day, 3.0 ACH50 | Sealed in one layer; testable before drywall | Same, with plates and holes foamed | Each missed hole adds leakage, harder to reach after drywall |
| Installed cost | FoamGuard $1.50–$2.25 per board foot: $5.25–$7.88 per sq ft at 3.5 in. | FoamGuard $3.00–$4.50 per sq ft for the 2 in. of foam, plus an R-13 batt at $1.07–$1.89 per sq ft (market range) | R-23 mineral wool $2.56–$3.78 per sq ft (market range), plus wrap |
In hot-box testing, 3 inches of closed-cell cut heat loss 90%; each added inch gained 1 to 2 points (the data).
Blower door, HVAC and fresh air
A tight house is planned with its mechanical system. The code allows the blower-door test once envelope penetrations are sealed, so test right after the foam, while they are still exposed.
A new house that passes the test needs whole-house mechanical ventilation, about 50 to 60 cfm for 2,000 square feet and three bedrooms. An ERV moves heat and moisture, which suits humid summers (fresh air after spray foam).
The code requires equipment sized by ACCA Manual S from a Manual J load. Forty real Manual J loads averaged 1,431 square feet per ton; a common rule of thumb uses 500. In our Erie load calculation, air leakage was 41% of the heating load; closed-cell at the rim joists and a sealed, topped-up attic floor cut the load from 41,430 to 31,640 Btu/h, close to one nominal ton. Give the HVAC designer the foam scope and target ACH50 first (HVAC size).
Working with builders and architects
We partner with builders and architects on scope and schedule. The schedule runs: dried-in shell, rough-ins, inspections, spray foam, insulation check, drywall. Pennsylvania's UCC requires work to stay accessible until inspected. On spray day the framing reads 19% moisture or less (18% for some products), surfaces sit at least 5°F above the dew point, and other trades work elsewhere. Insulation for architects covers code values and MasterFormat sections.
Drywall is the thermal barrier in living space; service-only attics and crawlspaces can use an ignition barrier. Foam left exposed in an unfinished basement takes drywall or a coating listed for that foam, which we offer as an add-on; an attached garage takes drywall (thermal vs ignition barriers).
Board-foot math for a 2,240-square-foot house
Board feet are square feet × inches. Assumptions: two stories on a 28 × 40-foot footprint, 18 feet of wall height, an unvented 6/12 roof.
- Walls: 136 ft of perimeter × 18 ft = 2,448 sq ft, minus 348 sq ft of windows and doors (20 at 15 sq ft, two at 24) = 2,100 sq ft × 3.5 in. = 7,350 board feet.
- Roof deck, all foam: 1,120 sq ft × 1.118 for the slope = 1,252 sq ft, plus two 98-sq-ft gables (28 × 7 ÷ 2) = 1,448 sq ft × 7 in. = 10,136 board feet.
- Total: 17,486 board feet × $1.50 = $26,229; × $2.25 = $39,344.
- Hybrid roof: 1,448 sq ft × 3 in. = 4,344 board feet; with the walls, 11,694 board feet = $17,541–$26,312, plus the batts below.
The written quote and how the job goes
Every quote lists each area, thickness, product and R-value and the board feet (how to read a quote). Quotes are good for 30 days, and the price is fixed for 3 months once signed.
- We spray to ¼ inch over the nominal depth and check it with a depth gauge.
- Trim and clean-up are included.
- Re-occupancy is typically 24 hours after spraying.
- At completion we email photos, a thermal scan and a project file with drum lot numbers.
- Minimum job $1,500; 0% APR financing up to 22 months for qualified buyers.
- A Craftsman's Promise, a 5-year written workmanship warranty with a lookup ID, plus the manufacturer's written product warranty, issued once the job is paid in full.
Send the plans and the code path: Price My Project.
Read next: Spray Foam in New Construction: When It Fits the Schedule · Flash and Batt in Zone 5: How Much Foam Before the Batts · Insulation for Architects: Specifying Closed-Cell Spray Foam · Spray foam and HVAC size: a heating-load calculation for an Erie house · Insulation Cost Calculator.
Questions
When does spray foam go in on a new house?
After the house is dried in and the rough-ins pass inspection, before the insulation check and drywall.
Does a spray-foamed new house need mechanical ventilation?
Yes. A new house that passes the blower-door test needs whole-house ventilation, about 50 to 60 cfm for 2,000 square feet and three bedrooms.
Can you spray foam a new house in winter?
Yes. Winter-grade foams are rated for surfaces down to about 15 to 30°F, by product, with dry or vented temporary heat.
Sources
- Pennsylvania Energy Code: 2021 IECC with PA amendments, effective January 1, 2026 — Insulation Institute (NAIMA)
- 2021 Energy Code Compliance, 1 & 2 Family Dwellings (zone 5 table; 3 ACH as amended by PA UCC) — Buffalo Township, PA
- 2021 UCC Code Update and Implementation — City of York, PA
- 34 Pa. Code § 403.64, Inspections — Cornell Legal Information Institute
- 2021 International Residential Code, Chapter 8, Section R806.5 and Table R806.5 — ICC (copy hosted by GreenBuildingAdvisor)
- 2021 IECC Significant Changes: Section C402.5, air barriers and testing — ICC
- HEATLOK HFO High Lift Technical Data Sheet — Huntsman Building Solutions
- ICC-ES ESR-2642, WALLTITE closed-cell foams — ICC Evaluation Service
- WALLTITE Series HFO Closed-Cell SPF Application Guidelines — BASF
- Flash-and-Batt Insulation: Good Idea or Bad Practice? — Journal of Light Construction
- Vapor Retarders — Insulation Institute (NAIMA)
- Types of Insulation — U.S. Department of Energy
- Erie, PA average temperatures by month, 1991–2020 NOAA normals — Current Results
- Erie International Airport (725260) design conditions, ASHRAE Handbook 2025 values — climate.onebuilding.org
- Lake Effect Snow — National Weather Service
- Balanced Ventilation: Understanding the Options — Pennsylvania Housing Research Center, Penn State
- ACCA Manual S — Air Conditioning Contractors of America
- Manual J load calculations vs. rules of thumb — ACCA HVAC Blog / Energy Vanguard
- How Contractors Really Size Air Conditioning Systems — Florida Solar Energy Center
- Spray Foam Requirements for Thermal Barriers and Ignition Barriers in the IRC — Pennsylvania Housing Research Center, Penn State
- Know the Code: Using Spray Foam Insulation in Attics and Crawl Spaces — Center for the Polyurethanes Industry
- Attic Air Sealing Project — ENERGY STAR
- Spray Polyurethane Foam Insulation: Health and Safety Recommendations for Consumers — U.S. CPSC staff
- Insulation Cost Calculator: installed prices by type, October 31, 2026 — FoamGuard
