Short answer
FoamGuard sprays 2 to 3 inches of closed-cell foam directly onto the steel of pole barns and metal buildings across Western Pennsylvania. At about R-7 per inch, one layer insulates, stops air and slows vapor, so inside air never reaches the cold metal to condense.
Key points
- Closed-cell foam bonded to steel stops air at about 1 inch and is a Class II vapor retarder at about 1¼ to 1⅞ inches.
- Aged HFO closed-cell runs about R-6.3 to R-7.4 per inch; 2 inches is about R-14.
- On a 0°F night, bare steel over a 60°F shop sits near 12°F; the room side of 2 inches of foam stays near 57°F.
- In hot-box testing, closed-cell cut heat loss 72% at 1 inch, 86% at 2 and 90% at 3.
- Two inches under a 40×60 pole barn roof is about 5,060 board feet, or $7,600–$11,400.
Closed-cell foam keeps inside air off cold steel
Steel conducts heat almost instantly, so its inside face runs near the outdoor temperature. In Western Pennsylvania's Climate Zone 5, on a 0°F night, bare steel over a shop at 60°F and 50% relative humidity sits near 12°F, far below that air's 41°F dew point. Moisture condenses or freezes on it, then rains down when the sun hits the roof. Damp spring and fall mornings wet the steel too. Near Erie, lake-effect bands can drop 2 to 3 inches of snow an hour, and every truck that comes in snow-covered adds water to the air.
Closed-cell spray foam bonds to the back of the panel with no gap behind it. One application stops air, slows vapor, insulates at about R-7 per inch and adds racking strength to the panels. At 2 inches, its room side stays near 57°F on that 0°F night, so inside air never meets cold metal. That is how foam stops a dripping roof; leaks get repaired first.
We spray only closed-cell on metal: open-cell lets water vapor through to the cold steel, where it condenses (closed-cell vs open-cell).
What we spray, by building
Use sets the thickness; past 3 inches, each added inch cuts heat loss a point or two (hot-box data, how thick spray foam should be).
| Area | Foam | Typical thickness | R-value | Why |
|---|---|---|---|---|
| Roof deck, unheated storage | Closed-cell | 2 in. | About R-14 | Stops the drip; past the Class II threshold |
| Walls, gables, roof: shop heated part-time | Closed-cell | 2 in. | About R-14 | Dry steel, 86% less heat loss |
| Walls, gables, roof: shop heated all winter | Closed-cell | 2–3 in. | About R-14 to R-21 | Sized for heat and condensation |
| Livestock or horse barn walls | Closed-cell | 3 in. | About R-21 | Humid air against cold panels |
| Living space in a steel shell | Closed-cell | About 3.3 in. walls, 7 in. roof | R-23 walls, R-49 roof | Pennsylvania's energy code |
R-values are at about R-7 per inch; each quote lists the data-sheet value at the thickness sprayed.
A cold-storage building that is never heated needs foam only on the roof. A heated shop gets walls, gables and roof (heated garage and workshop guide). Animal barns need ventilation first and a liner over foam that animals can reach. On a 60 × 49 horse barn in West Middlesex, we sprayed 3 inches on 2,676 square feet of 17-foot walls, R-22.2 on the data sheet, to stop condensation running down the panels. A house in a steel shell follows the residential energy code; see barndominium insulation.
Closed-cell spray foam vs blanket, foil and board
Four ways to insulate steel, from pole barn insulation options:
| Closed-cell spray foam | Vinyl-backed fiberglass blanket | Reflective bubble foil | Rigid foam board | |
|---|---|---|---|---|
| R-value | About R-6.3 to R-7.4 per inch (aged) | R-10 to R-30 per blanket (nominal) | Depends on the air space beside it | R-3.8 to 4.4 (EPS), R-5 (XPS), R-6 (polyiso) per inch |
| Stops air | Yes, bonded to the steel | Only where the facing is sealed | Only where seams are taped | Only where every joint is sealed |
| Vapor control | Class II at about 1¼ to 1⅞ in. | Vinyl about 1.0 perm; foil and PSK facings 0.02 to 0.09 perm | Low-perm film, many seams | Varies by product and facing |
| At framing and seams | One bonded layer | Crushed at girts; a tear lets air reach the steel | Condensation moves to the foil | A gap at a corner or girt lets air behind it |
| When it goes in | Any time after the steel is on | As the steel goes on | During construction | After framing |
| What to price | $1.50–$2.25 per board foot, plus a thermal barrier in a work space | Blanket, tape, liner, labor; steel removal on an existing building | Foil, tape, labor | Board, tape, gypsum liner, labor |
What a 40×60 pole barn costs, worked out
Spray foam is priced by the board foot: board feet = square feet × inches. The 40×60 example from what it costs to spray a pole barn has 14-foot walls, a 4/12 roof and nothing deducted:
- Walls: 200 ft perimeter × 14 ft = 2,800 sq ft
- Gables: 2 × (20 ft half-width × 6.67 ft rise) = about 267 sq ft
- Roof deck: 2,400 sq ft footprint × 1.054 pitch factor = about 2,530 sq ft
- Total: about 5,596 sq ft
At FoamGuard's $1.50–$2.25 per board foot for closed-cell:
- Roof only, 2 inches: 2,530 × 2 = 5,060 board feet, about $7,600–$11,400
- Walls, gables and roof, 2 inches: 5,596 × 2 ≈ 11,193 board feet, about $16,800–$25,200
- Walls, gables and roof, 3 inches: 5,596 × 3 ≈ 16,789 board feet, about $25,200–$37,800
Doors and windows are deducted first: on our Blair County metal building, 498 square feet of openings were deducted, leaving 4,724 square feet sprayed at 2 inches, R-14.8 on the data sheet. The minimum job is $1,500. Qualified buyers get 0% APR financing up to 22 months. For open-cell or other insulation, price your dimensions in the free insulation cost calculator.
Open this 40×60 pole barn in the calculator and change the length, width, wall height, doors and foam depth to match yours; it prices closed-cell, open-cell and the other insulation types side by side.
How the job goes
- Quote. Every area, thickness, product and R-value in writing; good for 30 days, price fixed for 3 months once signed.
- Prep. Old blanket or foil comes out so the foam bonds to the steel. We arrange removal at cost, or you hire it, and we project-manage it at no markup. The steel must be dry and frost-free (spray foam in winter).
- Fire protection. Foam in a shop where people work gets an approved thermal barrier, such as 1/2-inch gypsum, or a coating listed for that foam, which we offer as an add-on. An attic entered only for service may use an ignition barrier per code (which barrier applies).
- Spray day. Nominal depth is the minimum: we spray to +¼ inch, verified with a depth gauge. Trim and clean-up are included. Re-occupancy is typically 24 hours.
- Completion. Photos, a thermal scan and a project file with lot numbers, emailed. A Craftsman's Promise, our 5-year written workmanship warranty with a lookup ID, plus the manufacturer's written product warranty, issued once the job is paid in full.
Read next: Pole Barn Insulation: Spray Foam vs Blanket vs Foil vs Board · Why Your Pole Barn Roof Drips and How to Stop It · What It Costs to Spray Foam a 30×40 or 40×60 Pole Barn · Metal building, 28 × 73 × 17: walls and roof deck at 2 inches · Insulation Cost Calculator.
Questions
Is spray foam worth it on a pole barn or metal building?
Yes. Closed-cell foam is insulation, air barrier and vapor retarder in one bonded layer at about R-7 per inch, sprayed onto a finished building with no panels removed.
Can I use open-cell spray foam on a metal building?
No. Open-cell lets water vapor through to the cold steel, where it condenses and drips. We spray closed-cell on metal.
How do I stop my pole barn roof from dripping?
If it's condensation, 2 inches of closed-cell on the roof steel keeps inside air off the cold metal. Leaks get repaired first.
How thick should spray foam be on a pole barn?
Two to three inches of closed-cell on walls and roof. Living space must meet the energy code: about 3.3 inches for R-23 walls.
Does spray foam in a shop need a thermal barrier?
Yes, where people work: 1/2-inch gypsum or a coating listed for that foam, which we offer as an add-on. Your code official rules on detached shops and farm buildings.
Sources
- Typical R-Values and Vapor Retarder Classifications of Common Insulation Materials — PNNL Building America Solution Center
- Facts About Moisture and Fiber Glass Metal Building Insulation (MB306) — NAIMA
- NAIMA 202 Standard for Flexible Fiber Glass Insulation for Metal Buildings — NAIMA
- Radiant Barriers — U.S. Department of Energy
- Types of Insulation — U.S. Department of Energy
- HEATLOK HFO High Lift Technical Data Sheet (rev. 11.25.24) — Huntsman Building Solutions
- WALLTITE Max Series Technical Data Sheet — BASF
- ENERTITE G Open-Cell Technical Data Sheet — BASF
- Pennsylvania Energy Code: 2021 IECC with PA Amendments — NAIMA
- Lake Effect Snow — National Weather Service
- Know the Code: Using Spray Foam Insulation in Attics and Crawl Spaces — Center for the Polyurethanes Industry
