Short answer
FoamGuard sprays 2.5 inches of closed-cell foam on crawl space and basement foundation walls, about R-17.5, and 2 to 3 inches on the rim joist. One bonded layer insulates, air-seals and slows vapor, and the pipes and ducts end up inside the warm envelope.
Key points
- Closed-cell foam is insulation (about R-7 per inch), air barrier and vapor retarder in one bonded layer.
- In a sealed crawl, the insulation goes on the foundation walls and rim joist, not under the floor.
- 2.5 inches of closed-cell gives about R-17.5, above the 2021 IECC's R-15 for Zone 5 foundation walls.
- Water comes first: drainage, crack repair and a dry wall before any foam.
- A 1.25-inch layer of closed-cell foam tested 65 times more resistant to radon migration than a 6 mil polyethylene sheet.
Seal the crawl and insulate the walls
Closed-cell foam on the foundation walls and rim joist insulates, air-seals and slows vapor in one pass. Western Pennsylvania is IECC Climate Zone 5A: long winters (Erie's record 2017–18 season brought 166.3 inches of snow) and humid summers. Building Science Corporation puts basement heat loss at upwards of 20 percent of a home's heating and cooling load.
A vented crawl is treated as outdoors, with the insulation in the floor above (R-30 under the 2021 IECC). Humid summer air cools against the ground and ducts sweat; in winter the pipes sit in near-outdoor air. A sealed crawl is part of the house. Under IRC R408.3, the vents close, the ground gets a continuous Class I vapor retarder, and the air is exhausted or supplied at 1 cfm per 50 square feet of floor, or dried with a dehumidifier. Combustion air for any furnace or water heater in the crawl gets sorted out first.
In a sealed crawl, foam goes on the walls, not under the floor, where it would leave the walls and ground cold and cut the crawl off from the heat above (crawl space spray foam). A small, dry crawl with no ducts or water lines, under an insulated, air-sealed floor, can stay vented.
Dry the wall first: poured, block and stone
Foam bonds to a clean, dry wall, and it is insulation, not waterproofing (is spray foam waterproof?). Before we spray, downspouts discharge well away, the ground slopes away from the house, cracks and failed mortar are repaired, and groundwater at the wall-floor joint gets a drain and sump. Mold on framing is removed and its moisture source fixed first.
Poured walls are smooth, and foam fills the form-tie holes. Block has hollow cores; open cores along the top course are an air path to the sill, so we foam them closed. Old stone foundations often wick ground moisture, so drainage comes first (spray foam in older homes); then foam bonds to the uneven face as it is.
The rim joist, the leakiest line in most basements, is part of every job. In ASTM C-236 hot-box testing, 3 inches of closed-cell cut heat loss through the tested wall assembly by 90% (thickness case study). We check the sill for rot and for 19% moisture or less first (rim joist spray foam).
What we spray, and the code that covers it
| Area | Foam | Typical thickness | R-value | Why |
|---|---|---|---|---|
| Basement foundation walls | Closed-cell | 2.5 in. | About R-17.5 | Clears R-15 continuous; bonds to concrete, block or stone |
| Crawl space walls (sealed crawl) | Closed-cell | 2.5 in., liner to sill | About R-17.5 | Clears R-15 continuous; tolerates ground moisture |
| Rim joist and sill plate | Closed-cell | 2–3 in. | About R-14 to R-21 | Seals the leakiest line; can stay bare up to 3¼ in. |
R-values use about R-7 per inch, a typical aged value for HFO closed-cell; your quote lists the data-sheet value. At 2.5 inches the foam is its own vapor retarder, so no plastic goes over it. The DOE says open-cell should not be used below ground level, where it could absorb water.
Foam in a basement gets a thermal barrier (IRC R316.4): ½-inch drywall, or a coating listed for that foam, which we offer as an add-on. A crawl entered only for service may use an ignition barrier instead (R316.5.4), such as ⅜-inch gypsum board.
About 40% of Pennsylvania homes have radon above EPA's 4.0 pCi/L action level (Pennsylvania DEP). Closed-cell from footing to sill seals the slab–wall joint and the rim, the two leakiest lines in a basement. In independent lab testing, a 1.25-inch layer of the closed-cell foam tested was 65 times more resistant to radon migration than a 6 mil polyethylene sheet (radon case study). Foam is part of sealing, not a mitigation system by itself: test after the work, and at 4.0 pCi/L or higher a state-certified mitigator installs a fan system.
Closed-cell vs board vs batts
| Closed-cell on foundation walls | Rigid board on walls | Fiberglass batts between floor joists | |
|---|---|---|---|
| R per inch | About 7 (aged HFO) | EPS 3.8–4.4; XPS 5; polyiso about 6 | About 3.7–4.3 |
| Air barrier | Yes, bonded, at about 1 in. | Only if every seam and edge is taped | No; air passes through |
| Vapor control | Class II by about 2 in. | Depends on the board | Unfaced is vapor-open |
| Seams and framing | None; fills tie holes and block faces | Air can move behind it on uneven walls | Gaps at joists, pipes and wires |
| Pipes and ducts | Inside the insulated envelope | Inside the insulated envelope | Outside the insulated envelope |
| Installed cost | $3.75–$5.63 per sq ft at 2.5 in. | $2.45–$4.15 per sq ft at R-15 (calculator) | Lowest of the three (calculator) |
The board-foot math, and how the job goes
Board feet are square feet × inches. Take a 30 × 40 ft basement with 7-ft walls:
- Walls: 140 ft of perimeter × 7 ft = 980 sq ft × 2.5 in. = 2,450 board feet.
- Rim joist and sill: 140 ft × about 1 ft = 140 sq ft × 3 in. = 420 board feet.
- Total: 2,870 board feet × $1.50–$2.25 = $4,305–$6,458, before windows are deducted or any prep is added.
As a crawl with 4-ft walls, the same footprint is 1,400 board feet of wall plus 420 at the rim: 1,820 board feet, or $2,730–$4,095. Our minimum job is $1,500. To price board, batts or open-cell, use the free calculator.
Every written quote lists each area, thickness, product and R-value; quotes are good 30 days, and the price is fixed for 3 months once signed. We spray to +¼ inch over nominal depth and check with a depth gauge. Trim and clean-up are included; re-occupancy is typically 24 hours. At completion we email photos, a thermal scan and a project file with the foam's lot numbers. We don't remove old insulation ourselves: we arrange removal at cost, or you hire it, and we project-manage at no markup. Once the job is paid in full, you get A Craftsman's Promise, our 5-year written workmanship warranty with a lookup ID, plus the manufacturer's written product warranty. Financing is 0% APR up to 22 months for qualified buyers. Get your number.
Read next: Crawl Space Spray Foam: Vented vs Sealed Crawls · Basement Wall Insulation in Zone 5: Spray Foam vs Board · Rim Joist Spray Foam: How Much and Why It Matters · Closed-cell spray foam for radon abatement: 65× more resistant than 6 mil poly · Insulation Cost Calculator.
Questions
Should my crawl space be vented or sealed?
Sealed, when it holds ducts or water lines: closed vents, a sealed ground liner, closed-cell foam on the walls and rim, and managed air under IRC R408.3.
Does spray foam stop radon?
Closed-cell foam seals the slab–wall joint and the rim joist, the two leakiest lines in a basement, and a 1.25-inch layer tested 65 times more resistant to radon migration than 6 mil polyethylene. Test after the work; at 4.0 pCi/L or higher, a state-certified mitigator installs a fan system.
Will a sealed crawl keep my pipes from freezing?
It puts the water lines inside the insulated envelope instead of in near-outdoor air. Floor insulation in a vented crawl leaves them on the cold side.
Will my floors be warmer?
The floor sits over a space that stays close to indoor temperature instead of outdoor air, and the sealed rim joist closes the biggest leak line at floor level.
Can the foam stay exposed in a basement or crawl space?
Basement foam gets ½-inch drywall or a listed coating. A service-only crawl can use an ignition barrier, and rim joist foam can stay bare up to 3¼ inches thick.
Sources
- Crawlspaces Builder Brief — Pennsylvania Housing Research Center, Penn State
- 2009–2021 IECC and IRC Minimum Insulation Requirements — DOE Building America Solution Center
- Typical R-Values and Vapor Retarder Classifications for Common Insulation Materials — DOE Building America Solution Center
- BSD-103: Understanding Basements — Building Science Corporation
- Info-408: Critical Seal (Spray Foam at Rim Joist) — Building Science Corporation
- IRC Spray Foam Thermal Barriers and Ignition Barriers — Pennsylvania Housing Research Center, Penn State
- Types of Insulation — U.S. Department of Energy
- Revised Erie, PA Snowfall Records — National Weather Service Cleveland
- DEP Encourages Pennsylvanians to Test Their Homes for Radon — Pennsylvania DEP
- One-Step Radon Protection (HEATLOK HFO Pro and HFO High Lift) — Huntsman Building Solutions
- HEATLOK HFO High Lift Technical Data Sheet — Huntsman Building Solutions
- ICC-ES Evaluation Report ESR-2642: WALLTITE closed-cell foams — ICC Evaluation Service (BASF)
- Insulation Cost Calculator — FoamGuard
