Short answer
The foam itself doesn't feed mold. Closed-cell foams are tested for it, and HEATLOK HFO High Lift and WALLTITE both list no fungal growth on the ASTM C1338 fungi resistance test. Mold needs moisture and oxygen, and closed-cell foam bonded to the wood keeps out the humid air and condensation that let it grow inside walls and roofs. What foam doesn't do is fix mold that is already there: that gets removed first and its moisture source fixed.
How FoamGuard handles it
- We check before we spray. A thermal camera scan finds cold or damp patterns, and wood has to be dry enough for the foam: manufacturers' data sheets typically set wood moisture at 19% or less.
- We never spray over mold or wet wood. That area is marked and held back until the cause is fixed and the mold removed (what happens if we find mold).
- Closed-cell goes against cold surfaces such as roof decks and steel in this climate, because it is the air barrier and, at about an inch and a half to two inches, the vapor retarder in one layer.
- Open-cell under a cold roof deck needs a Class II vapor retarder in Climate Zone 5 (IRC R806.5), so we don't use it there without one.
What's typical elsewhere
EPA's guidance is that mold can grow on virtually any organic material as long as moisture and oxygen are present, and that "the key to mold control is moisture control." Building science puts the cold-climate mechanism plainly: closed-cell foam against the roof sheathing "prevents warm, humid indoor air from reaching the back (underside) of roof sheathing" where it would condense (Building Science Corporation, BSD-149). No insulation, foam included, fixes a roof leak or kills existing mold.
What the data sheets say
| Property | HEATLOK HFO High Lift (Huntsman) | WALLTITE LWP (BASF) |
|---|---|---|
| Fungi resistance, ASTM C1338 | No fungal growth | Pass (no growth) |
| Water absorption by volume, ASTM D2842 | 0.87% | Under 0.30% |
| Air permeance at 1 inch, ASTM E2178 | Under 0.02 L/s·m² | Under 0.02 L/s·m² (air impermeable) |
| Water vapor | Class II vapor retarder (1 perm or less) at 1.875 in | Under 1.0 perm at 1.5 in |
ASTM C1338 tests new insulation materials for their ability to resist fungal growth under conditions that favor it. It describes the material, not the building or what settles on it later, which is why keeping water out is still the rule.
Where mold still shows up
- Bulk water: a roof leak or a plumbing leak wets the wood regardless of the insulation. EPA lists roof materials wetted by leaks and pipes that leak or condense among the common places for hidden mold.
- Vapor-open insulation on cold surfaces: open-cell foam or fiberglass against a cold roof deck or a basement wall lets moist air reach the cold surface. See open-cell spray foam under a roof deck and basement wall insulation.
- Mold that was there before: foam sealed over it doesn't solve it (next question).
Want a number for your own project? Price My Project, book a free visit or call (814) 208-3478.
Does spray foam kill mold?
No. And killing it isn't enough anyway: EPA says dead mold may still cause allergic reactions, so it has to be removed.
Can mold grow on the surface of the foam?
The foam itself isn't food for it; the test is run on new, clean material. EPA's rule applies to everything in a building: control the moisture and you control the mold.
Is closed-cell foam a vapor barrier?
It is a Class II vapor retarder, about 1 perm or less, at roughly an inch and a half to two inches depending on the product.
Sources
- Huntsman Building Solutions: HEATLOK HFO High Lift technical data sheet (rev. 11.25.24)
- BASF: WALLTITE LWP Series technical data sheet (Nov. 7, 2023)
- ASTM C1338: Standard Test Method for Determining Fungi Resistance of Insulation Materials and Facings
- US EPA: Mold Course, Chapter 2 (Why and Where Mold Grows)
- US EPA: A Brief Guide to Mold, Moisture and Your Home
- US EPA: Should I use bleach to clean up mold?
- US EPA: Hidden Mold (archived)
- Building Science Corporation, BSD-149: Unvented Roof Assemblies for All Climates (Schumacher)
